隨著電力電子技術和變流控制技術的飛速發展，高精度可控變流技術的成熟和普及，生產高壓開關柜分階段恒流充電模式已經基本被充電電流和充電電壓連續變化的恒壓限流充電模式取代。主導充電工藝的還是恒壓限流充電模式。高壓開關柜哪家好接觸式充電的最大問題在于它的安全性和通用性。為了使它滿足嚴格的安全充電標準，必須在電路上采用許多措施使充電設備能夠在各種環境下安全充電，恒壓限流充電和分階段恒流充電均屬于接觸式充電技術。新型的電動汽車感應充電技術發展很快。

對于配電變壓器容量在100kV·A及以上的配電箱體，在箱內散熱窗靠側壁處，應考慮到安裝溫控繼電器（JU-3型或JU-4超小型溫度繼電器）和軸流風機，安裝在控制電器板上方左側面的箱體上，以便使箱內溫度達到一定值時（如40℃）能自動啟動排氣扇，強行排出熱量以使箱體散熱。

用軟刷或吹風清除屏板插件和全部電磁開關零件的積塵,并檢查控制柜內電器開關觸頭的狀態,接觸情況,線圈外表的絕緣以及機械部件的動作是否可靠,更換熔絲時,應使熔斷電流與該回路的電流相匹配。

改進原配電箱的低壓電容器組的接線方式，將其安裝位置由交流接觸器上樁頭，改成接在配電箱低壓進線與計量表計之間。防止因運行中電容器電路發生缺相故障或電容器損壞時，造成計量裝置計量不準確。此外，電容器選擇型號應為BSMJ系列產品，以保證元件質量可靠、安全運行。

配電變壓器的低壓側總過流保護熔斷器的額(e)(e)(e)定電流，應大于配電變壓器的低壓側額(e)(e)(e)定電流，一般取額(e)(e)(e)定電流的1.5倍，熔體的額(e)(e)(e)定電流應按變壓器允許的過負荷倍數和熔斷器特性確定。出線回路過流保護熔斷器的熔體額(e)(e)(e)定電流，不應大于總過流保護熔斷器的額(e)(e)(e)定電流，熔體的額(e)(e)(e)定電流按回路正常最大負荷電流選擇，并應躲過正常的尖峰電流。