選用節能型交流接觸器（類似CJ20SI型）產品，并注意交流接觸器線圈電壓與所選剩作電流動作保護器的相對應接線端子相連，注意進行正確的負載匹配。選擇交流接觸器時，應選用其絕緣等級為A級及以上產品，必須保證其主回路觸點的額定電流應大于或等于被控制的線路的負荷電流。接觸器的電磁線圈額定電壓為380V或220 V

1.了解用戶所需,根據實際情況選擇最適合用戶的柜型。2.盡量采用國內知名廠家的國產柜型,不能盲目選擇技術參數比較高的進口配電柜,這樣易造成資源浪費。3.由于進口配電柜中所采用的主要元器件的品牌與柜體是一致的。所以選擇進口配電柜時,應注意主要元器件的參數,它必須能滿足用戶需要。

配電箱是按電氣接線要求將開關設備、測量儀表，保護電器和輔助設備組裝在封閉或半封閉金屬柜中或屏幅上，構成低壓配電箱。正常運行時可借助手動或自動開關接通或分斷電路。故障或不正常運行時借助保護電器切斷電路或報警。借測量儀表可顯示運行中的各種參數，還可對某些電氣參數進行調整，對偏離正常工作狀態進行提示或發出信號。

隨著電力電子技術和變流控制技術的飛速發展，高精度可控變流技術的成熟和普及，專業分體式充電樁分階段恒流充電模式已經基本被充電電流和充電電壓連續變化的恒壓限流充電模式取代。主導充電工藝的還是恒壓限流充電模式。分體式充電樁哪家好接觸式充電的最大問題在于它的安全性和通用性。為了使它滿足嚴格的安全充電標準，必須在電路上采用許多措施使充電設備能夠在各種環境下安全充電，恒壓限流充電和分階段恒流充電均屬于接觸式充電技術。新型的電動汽車感應充電技術發展很快。